Skip to content
SKU BU-AVA-CR14-OSS-MC10

Avantone CR14 Ribbon Microphone w/ Shock Mount, Aluminum Case, Stand, and 10ft Cable

$339.99

Avantone CR14 Ribbon Microphone w/ Shock Mount, Aluminum Case, Stand, and 10ft Cable

$339.99

Manufacturer's Description

Avantone CR14 Ribbon Microphone with Shock Mount & Aluminum Case

Avantone CR-14 Ribbon Microphone

The Avantone ""Cabernet (C-series)"" mics are designed to offer true professional performance. They will meet or surpass the performance and specifications of much higher priced mics. The Avantone CR-14 is truly a gorgeous looking and sounding microphone. The design, character and performance is comparable to some of the very finest Ribbon mics...but at a fraction of their cost!

Our rugged CR-14 microphone body and inner assembly parts are precision machined of brass. Aesthetically, it features an elegant Cabernet Wine-Red finish, accented with polished nickel trim and a black grill. The CR-14 has a unique, ""retro"" body design

The transformer coupled output will yield pleasing professional results comparable to much more expensive designs. Any studio can proudly offer the CR-14 as a guitar cabinet, room mic, drum overheads, vocal mic or utility room mic due to its versatility...It exudes class visually as well as sonically.

Manufactured using the finest materials yielding a very solid feel, superb structural integrity and rugged reliability. The versatile CR-14 mic is able to produce professional results with a warm, pleasing sonic character.

The included Custom Retro Shockmount is superb in allowing a precise positioning of the mic while inhibiting the transfer of unwanted vibrations up into the mic. This isolation allows for superior professional results.

The CR-14's dual, low-mass ribbon element which enables a much better sensitivity rating than most single ribbon designs. This design lends to fast and accurate transient response, ultra-high 148 dB SPL capability, and overall stunning realism. It has a figure-8 audio directionality (pickup) pattern via front and rear, with extended sweet spots (as compared to Large Diaphragm condenser mics & single ribbon designs).

The CR-14 has very low residual noise, with no internal active electronics to overload or produce distortion. It also requires no power supply.

Master MC-10 Microphone Cable, 10 ft

MC-10 Microphone Cable

On-Stage Stands 11657 MS9701TB+ (MS9701TBPLUS) Heavy-Duty Tele-Boom Mic Stand

Pro-level Platinum Series stands feature heavier diecast leg housings, thicker tubing and premium threads. A new ergonomic center clutch grip, coupled with an anti-rotating device on the lower shaft, makes for easy one-hand height adjustments. An all-metal boom clutch, zinc die-cast end caps, steel boom, and metal counterweight make the MS9701TB truly professional. The telescoping boom arm provides the right boom length for any application.

  • This heavy-duty Platinum Series stand is built to last
  • A steel 19""-30"" telescoping boom with metal clutch, zinc die-cast end caps, steel shafts, and metal counterweight make the MS9701TB truly professional
  • A new ergonomic center clutch grip that adjusts height from 36"" to 64"" , coupled with an anti-rotating device on the lower shaft, makes for easy
  • one-hand height adjustments
    Allen nuts and bolts in the leg housing allow for tension adjustments

Specifications

Avantone CR14 Ribbon Microphone with Shock Mount & Aluminum Case

  • Type: Ribbon Microphone
  • Ribbon: Dual Ribbon / Pure Aluminum / 35mm x 5mm / 2 microns thick
  • Polar Pattern: Figure of 8
  • Frequency Response: 30Hz - 15kHz +/- 3dB
  • Output Impedance: <=600 Ohms
  • Recommended Load: Impedance 3000 Ohms
  • Maximum SPL: 145dB (0.5% THD @1000Hz)
  • S/N Ratio: 70dB re 1Pa
  • Sensitivity: -52 dBv +/- 2dB Re. (0dB=1V/Pa)
  • Output Connector: Male XLR 3 pin
  • Included Accessories: -Padded Wooden Box, Shockmount, Metal road case
  • Power Requirements: None
  • Finish: Polished Nickel trim / Metallic Cabernet Red Body
  • Weight: 16 oz (496 grams)
  • Dimensions: 1.45"" (37mm) x 6.89"" (175mm)

On-Stage Stands 11657 MS9701TB+ (MS9701TBPLUS) Heavy-Duty Tele-Boom Mic Stand

  • Height: 36""-64""
  • Base Spread: 24""
  • Boom Length: 19""-30""
  • Threading: 5/8""-27""
  • Construction: Steel and zinc
  • Color: Black