(6) Sennheiser e835 Dynamic Cardioid Vocal Microphones with SKB iSeries Mic Case & Cables

Sennheiser e835 Dynamic Cardioid Vocal Microphone (3-Pack)

• Pickup pattern: cardioid
• Transducer: pressure gradient dynamic
• Frequency response: 40Hz-16kHz
• Sensitivity (free field, no load): 2.7mV/Pa =/-51.4dB (odB=1V/Pa) =/-71.4dB (odB=1V/µbar) (USA)
• Nominal impedance at 1 kHz: 350 ohms
• Min terminating impedance: 1000 ohms
• Dimensions: 1-7/8" dia. x 7-1/8"L
• Weight: 11-2/3 oz.

SKB 3i-0907-MC6 iSeries Injection Molded (6) Microphone Case with Storage Compartment

 Manufacturer's Description

Sennheiser e835 Dynamic Cardioid Vocal Microphone (3-Pack)

Lead vocal stage mic, designed to perform under pressure. Uniform frequency pick-up pattern maintains signal quality when moving on and off axis during performance. Gentle presence boost to even tonal response ensures clarity and projection. Minimal proximity effect provides consistently clear bass and performance when singing closer to or farther from capsule.

Industry leading 10 year warranty! All parts and labor covered. *

Features

• Dynamic cardioid microphone for speech and vocals
• Cuts through high on-stage levels
• Clear reproduction with a high presence
• Consistent sound quality (varying distances, moving off axis)
• Handles high sound pressure levels
• Optional silent on/off switch
• Isolates handling noise, hum compensating coil
• Excellent feedback rejection
• Rugged metal housing

Pig Hog PHM20 8mm Microphone XLR Cable 20ft 

Pig Hog cables are precisely overbuilt to stand up to the most grueling tour conditions imaginable. They feature extra-thick 8mm wire, performance quality connectors, and tension-resistant stress relief. And with Pig Hog's "no question" lifetime guarantee, we've got your back for the life of the cable. Don't settle for those fat-free cables. Grab hold of a Pig Hog!

Features

• High performance microphone cable
• 8mm high quality rubber outer covering
• Heat shrink protected connectors
• Lifetime guarantee

SKB 3i-0907-MC6 iSeries Injection Molded (6) Microphone Case with Storage Compartment

The 3I-0907-MC6 holds six mics in a very compact case and is part of the 3I Waterproof Series of cases. It allows 6 mics to be stored horizontally on two separate layers of foam (3 on top and 3 on bottom). Each microphone cutout measures 1.5” wide by 6.75” long with two perforated removable foam pieces, one located on each end allowing microphone sizes up to 8.5” in length. By removing the perforated foam piece near the grill of the microphone you can change the shape from being round to square. This will accommodate other popular hand held microphones with square style grills such as the Sennheiser and Electro Voice mics. The 3I-0907-MC6 case measures 9” x 7” x 6” deep and is the most compact 6-mic case on the market. 3I Series injection molded waterproof cases are constructed of ultra high-strength polypropylene copolymer resin and feature a gasketed, waterproof and airtight, submersible design (IP67) that is resistant to corrosion and impact damage. Its continuous molded-in hinge, patented "trigger release" latch system, comfortable, snap-down rubber over-molded cushion grip handle, secure stacking, and automatic ambient pressure equalization valve (MIL-STD-648C) all contribute to its military grade design.

Features

• Ultra high-strength polypropylene copolymer resin
• UV, solvent, corrosion and fungus resistant (MIL-STD-810F)
• Complete gasket seal makes these cases absolutely watertight (MIL-STD-C-4150J)
• Automatic ambient pressure equalization value (MIL-STD-648C & IP67)
• Resistant to corrosion and impact damage
• Continuous molded-in hinge
• Patented "trigger release" latch system
• Rubber over-molded cushion grip handle
• Custom cut foam to hold six microphones